Computer Module Programming in Hillsboro, KS
The short answer
Module programming loads the correct software onto one of your vehicle's computers, or introduces a new part to the rest of the vehicle so it will accept it and work properly.
A modern car has many of these computers, called modules, running the engine, transmission, brakes, airbags, lights and locks. The usual story goes like this: the part got replaced, the truck still will not run right, and somebody says the words "dealer programming" while you picture a long drive and a week-long wait. We do that last step here in Hillsboro, so bring it in, or we will come and get it.
Call or text (620) 416-0008. Describe the noise. We'll do the rest.
We answer texts the same day we get them.
When a car needs module programming, decoded
Tap the ones that sound like yours.
You ticked 0. That is worth a look.
Text us which onesWhat module programming at Moxie actually looks like
We finish the job other shops cannot. A lot of repairs are mechanical work followed by a software step, and without the programming the vehicle may not start, may shift badly or may keep its warning lights on. We do both parts here.
We check before we program. A module can look dead when its wiring has failed, and programming it again will not help, so you only pay for programming when programming is the fix.
We keep the power steady the whole time. A voltage dip mid-programming can ruin a module, so your vehicle goes on a stable power supply before we start.
We save you the dealership trip. For most drivers in Marion, Harvey, McPherson, Chase and Lyon Counties, the nearest dealership service department is a long drive away and often booked out. Having it done in Hillsboro saves you the trip and the wait. We program every make in-house.
Why Hillsboro trusts Moxie with its module programming
-
No dealership trip
Dealer-level diagnostics and programming in Hillsboro, without the long drive or the wait.
-
We test before we program
We confirm the module is the problem before you pay to reprogram it.
-
An ASE-certified technician
Our technician is ASE certified in engine repair, automatic transmissions and drivetrains, and Moxie pays for ASE testing for the whole team.
-
NAPA 24/24 warranty
Repairs are covered for 24 months or 24,000 miles, nationwide.
Call or text (620) 416-0008. Describe the noise. We'll do the rest.
Module programming myths we hear at the counter
Hover or tap a card to flip it.
Sounds like yours? Tell us what it is doing and we will tell you straight.
Want the details?
Tap any of these to open it.
What sends a module in for programming around here
- A failed module was replaced, and the new one is blank or set up for a different vehicle
- A software fault the manufacturer has corrected with an update
- A new part, such as an injector or a battery, that the computer needs to be told about
- Settings lost when the battery went completely flat on a cold morning
- Water damage from a leak or flooded road, or a voltage spike that corrupted a module's software
How we approach module programming
- We confirm the module is actually the problem before programming anything, because reprogramming a computer will not fix a broken wire feeding it.
- We check whether a newer software version exists for your vehicle and whether it addresses your complaint.
- We connect a stable power supply before we start, since a voltage dip in the middle of programming can leave a module unusable.
- We program the module, then run any relearn or setup steps the manufacturer requires.
- We clear the codes, test drive the vehicle and confirm everything that talks to that module is working.
What we check before we program
- Battery and charging voltage, which must hold steady during programming
- The current software version on each affected module
- Stored codes across every module on the vehicle
- Wiring, power and ground to the module being programmed
- Communication between modules once programming is done
What the job usually turns out to be
- Programming a new or remanufactured replacement module
- Updating existing software to the manufacturer's latest version
- Registering a new battery, injector or other component with the vehicle
- Relearn procedures for the throttle, idle, transmission or steering angle sensor
- Repairing power or ground wiring so a module can be programmed and stay working
Module programming across five Kansas counties
We look after drivers across Marion County, Harvey County, McPherson County, Chase County and Lyon County, with free pickup and delivery within 40 road miles of 611 Orchard Dr, Hillsboro.
Module programming questions we hear every week
Do I have to go to the dealership to program a car computer?
Usually you do not. Much of the programming people are sent to the dealership for is work an independent shop with dealer-level equipment can do. There are exceptions on some makes and some modules, so call or text us with your vehicle and what you were told. We will give you a straight answer about whether we can do it here in Hillsboro.
Can I buy a used computer module and have it programmed?
It sometimes works, but it depends on the vehicle and the module. Some modules can be reset and set up for your vehicle, while others are locked to the vehicle they came from and cannot be reused. Text us the part number before you buy one, and we will tell you whether a used module is likely to work on your make and model.
How long does module programming take?
Programming a single module often takes an hour or two, including the checks before and the test drive after. A job that involves several modules, or a relearn that needs a specific drive cycle, can take longer. We will give you a time estimate as soon as we know exactly what your vehicle needs, so you can plan your day.